How do you reset the security system on a 2004 Pontiac Grand Am?

How do you reset the security on a Pontiac Grand Am?

Turn the key to the on position for 10 minutes then turn off, repeat 2 more times. the system should reset. Mine usually resets on the second time, if the security light stops flashing then i try to start.

How do I reset my Pontiac Anti theft system?

Turn the ignition to the “ON” position but do not start the engine. Wait 30 seconds and start the engine. Verify that none of the security lights on the dashboard are flashing or illuminated. The theft system has been reset.

What does the security light mean on a 2004 Pontiac Grand Am?

The security light staying on when you drive is an indication the system noticed a fault that needs to be diagnosed. I would try to replace the key first. Second if it continues replace the key cylinder. A cylinder replacement requires a system reset by cycling through the reset procedure 3X.

IMPORTANT:  Which phone is more secure?

How do I deactivate my anti-theft system?

To turn off the anti-theft system, use your remote to press the unlock button key. It is advised to use the key to unlock the door and turn on the ignition switch. If that does not work, try to lock the door on the driver’s side using the key while you are out of the car.

How do I bypass the security system on a 2004 Pontiac Grand Prix?

How do you reset the security system on a 2004 Pontiac Grand Prix…

  1. Exit the vehicle and stand next to the driver’s side front door.
  2. Press and hold the lock and unlock buttons on the keyless entry remote until the horn honks once and the lights flash briefly.

How do you reset the security system on a 2003 Pontiac Grand Am?

Turn the ignition key to the “Off” position for 10 seconds. 3. Repeat this process 3 times. This should reset the Security light/system and allow you to start your car.

How do I turn off anti theft without key fob?

Ways to stop a car alarm without a keyfob

  1. Check your owner’s manual. Every vehicle is different. …
  2. Lock your doors. …
  3. Turn the car on. …
  4. Turn the ignition to on and wait. …
  5. Pull the fuse for the alarm. …
  6. Pull the wires for your alarm. …
  7. Disconnect the battery.

What does it mean when your security light blinks?

The security alarming light blinks continuously even when the vehicle is OFF. The flashing red light is a security light to keep things safe. There are other blinking red LED lights on the dashboard as well. Other color LED lights also come active when the door is left open.

IMPORTANT:  How do you clean a vinyl sneeze guard?

How do I know if my car is in anti-theft mode?

If the security or anti-theft light is flashing when you attempt to start your car, and the engine does not crank or does not start, you have an anti-theft problem. The system may not be recognizing your key or keyless entry signal, or there may be a fault in the anti-theft module, keyless entry system or wiring.

What triggers theft deterrent system?

The theft-deterrent system in your vehicle may be triggered by the following: Key learning (copy of key made) Forced entry alarm (door, trunk, hood) Tilt/inclination.

How do you reset the anti-theft system on a 1996 Pontiac Grand Am?

How do i reset security code?

  1. Perform a security system relearn.
  2. Let the vehicle sit for more than 10 minutes with the key off.
  3. Attempt to start the engine, leave the key in the run position monitoring the security system indicator.
  4. After 10 minutes, the security indicator will change state.

How do you bypass the anti theft system on a Pontiac g6?

Method 3: Insert the key into your car’s door

Step 2: Turn the vehicle key to unlock the car door without releasing it. Hold the key for 30 seconds in the position. That will tell the system you have the right key, and it will enable you to be able to bypass the car’s alarm system.

How do I permanently disable GM PassLock?

How do I disable GM anti-theft system?

  1. Leave the ignition key turned to the “On” position after the vehicle has stalled and will not start.
  2. Look at the dashboard and locate the theft system light.
  3. Turn the ignition to the “Off” position to disable the PassLock system, and wait for 20 seconds for the system to reset.
IMPORTANT:  Is Windows Server 2019 secure?